GeneratorJoe Generators: Reliance Controls, Transfer Switches Generator, ,, , Model Furnace Series Manual Transfer Switches

Transfer Switches, Reliance Controls, Easy-Tran Furnace Series, Surface Indoor, Manual Transfer Switches, 20 Amp to 50 Amp Utility and Generator, Reliance Controls Generator

Furnace Series Manual Transfer Switches, Furnace Series

The Easy/Tran TF transfer switch is designed for the control of a single circuit, such as a forced-air furnace, in the event of a power failure. The attached 18” flexible aluminum conduit is pre-wired and allows the TF to be easily connected at the circuit breaker panel or the furnace. Power can be supplied from a portable generator, inverter, RV generator, fuel cell or any standby source capable of producing sufficient current to operate the desired load. The Easy/Tran is suitable for use with any portable or RV generator with a 15 amp, 120 VAC outlet and will operate a furnace motor of up to 2 HP.

The Reliance Easy/Tran® TF manual transfer switch is a truly low-cost method for using a portable or RV generator to operate your home’s forced-air furnace during a power outage. This will allow your family to stay warm and comfortable and prevent pipes from freezing. The Easy/Tran takes only minutes to install into your home’s furnace circuit and connects with most standard 15A extension cords (not included).

In the event of a power interruption simply use a standard grounded cord to connect the transfer switch to the standby power source. Then throw the double-throw switch on the TF from LINE to GEN and you have power to your forced-air furnace or any other 15A or 20A, 120VAC circuit. The light on the face of the TF will illuminate the area around the switch under standby power. The circuit breaker on the TF provides protection only when the switch is in the GEN position.

The TF151W can be connected to a 15A or 20A, 120VAC branch circuit. Power input, in the standby mode, is limited to 15A maximum. The TF201W can be connected to a 20A, 120VAC branch circuit only. Power input, in the standby mode, is limited to 20A maximum.

Standard Features

· Heavy-duty powder-coated steel enclosure.

· Completely pre-wired.

· Flexible aluminum conduit and fittings included.

· Built-in circuit breaker (UL489).

· Multiple knock-outs for more installation options.

· Built-in light illuminates area under standby power.

· Remarkably easy to install and easy to use.

· No need to throw the MAIN or branch circuit breaker.

· Can be placed anywhere between the branch circuit breaker in the load center and the furnace.

· Completely isolates the utility power from the standby power source.

· Two-year limited warranty.

· Listed by Underwriters Laboratories Inc. to standard UL1008.

· Suitable for use in accordance with article 702 of the National Electrical Code ANSI/NFPA 70.

	Power Inlet Boxes
GeneratorJoe!
	Click on pictures for larger view.
Model Number	PB15	PB20	PB30	PB31	PB33	PB50	PB51
Max. Input Amps	15	20	30	30	30	50	50
For Use With Models	15114	All 20A, 250V Models	All 30A, 250V Models	30114A	All 30A, 250V Models	All 50A, 250V Models	All 50A, 250V Models
Rating/Configuration	15A@125V 5-15	20A@250V L14-20	30A@250V L14-30	30A@125V L5-30	30A@3ØY/208V L21-30	50A@125VAC	50A@250VAC
Inlet	Yes	Yes	Yes	Yes	Yes	Yes	Yes
Circuit Breaker	No	No	No	No	No	No	No
Max. Gen. Input kW	1.875	5	7.5	3.75	10.8	6.250	12.5
Connector	5-15	L14-20	L14-30	L5-30	LI21-30 3 Phase	CS6365	CS6360
Dimensions, inches	6" H x 4" W x 2 5/8" D
Weight, lbs	2.5
Raintight NEMA 3R Power Inlet Boxes are designed for use with Pro/Tran transfer switches, Panel/Link manual transfer panels and generator-ready load centers. The power inlet box may be installed indoors or outdoors, in the area where the generator is being used. Using one of the four combination 1/2 inch and 3/4 inch knockouts (one on each side, bottom and back), the power inlet box can be wired directly to the transfer switch or panel. The exclusive patented design provides generous wiring space and facilitates rough-in. If you require a circuit breaker at the inlet box, use the PR Series inlet box that includes a circuit breaker. Select a box that matches the maximum amperage of the transfer switch.

	PR Power Inlet Boxes
	NEMA Type 3R Enclosure
Model Number	PR20	PR30	PR50
Description	Power Inlet Panel	Power Inlet Panel	Power Inlet Panel
Max. Input Amps	20	30	50
For Use With Models	All 20A, 250V Models	All 30A, 250V Models	All 50A, 250V Models
Rating/Configuration	20A@250V, L14-20	30A@250V, L14-30	50A@250V, C56365
Inlet	Yes	Yes	Yes
Circuit Breaker Included	Yes	Yes	Yes
Max. Gen. Input kW	5	7.5	12.5
Connector	L14-20	L14-30	CS6365
Dimensions, inches	9" H x 6" W x 5" D
Weight, lbs	1
The PR Series Power Inlet Boxes includes a circuit breaker. Select a box that matches the maximum amperage of the transfer switch. Raintight NEMA 3R power inlet box designed for use with the Pro/Tran transfer switches and Panel/Link manual transfer panels and generator-ready load centers. The power inlet box may be installed indoors or outdoors, in the area where the generator is being used. Using one of the four combination 1/2 inch and 3/4 inch knockouts (one on each side, bottom and back), the power inlet box can be wired directly to the transfer switch or panel. The exclusive patented design provides generous wiring space and facilitates rough-in.

	Power Inlet Kits - for use with Panel/Link®
Nobody gets the job done like GeneratorJoe!
Model Number	PK20	PK30	PK50
Max. Input Amps	20	30	50
For Use With Models	TRC, TRR, TTH, TTT, TTV & TWB	TRC, TRR, TTH, TTT, TTV & TWB	TRC, TRR, TTH, TTT, TTV & TWB
Rating/Configuration	20A@250V L14-20	30A@250V L14-30	50A@250V C56365
Circuit Breaker Included	No	No	No
Max. Gen. Input kW	5	7.5	12.5
Dimensions, inches	3" H x 3" W x 3" D
Weight, lbs	1
Suitable for installation into a 2 1/2" knockout on any indoor or outdoor Panel/Link transfer panel or lead center, TRC series and larger. UL listed.

	Wiring Devices
GeneratorJoe!
GeneratorJoe!	Click on pictures for larger view.
Model Number	L1420C	L1420P	L1430C	L1430P	LL550C	LL550P	L1420R	L1430R
Max. Input Amps	Connector	Plug	Connector	Plug	Connector	Plug	Receptacle
For Use With Models	20A@250V L14-20C	20A@250V L14-20P	30A@250V L14-30C	30A@250V L14-30P	50A@250V CS6364	50A@250V CS6365	20A@250V L14-20R	30A@250V L14-30R
Inlet Included/ Rating/Configuration	20216A, R20216B & PB20	All 20A, 250V Models	30216A, R30216B, 30310A, R30310B & PB30	All 30A, 250V Models	Panel/Link®	Panel/Link®	All 20A, 250V Models	All 30A, 250V Model
Max. Gen. Input kW	5	5	7.5	7.5	12.5	12.5	5	7.5
All Reliance plugs, connectors and receptacles are made in the USA and listed by Underwriters Laboratories Inc.

	Power Cords
Nobody gets the job done like GeneratorJoe!
Model Number	PC2010	PC2020	PC2040	PC3010	PC3020	PC3040	PC5010	PC5020	PC5040
Length Ft.	10	20	40	10	20	40	10	20	40
Amps	20	20	20	30	30	30	50	50	50
Voltage	125/250VAC	125/250VAC	125/250VAC	125/250VAC	125/250VAC	125/250VAC	125/250VAC	125/250VAC	125/250VAC
NEMA Configuration	L14-20	L14-20	L14-20	L14-30	L14-30	L14-30	CS6364	CS6364	CS6364
Shipping Weight, lbs	3.5	5	7.5	3.5	5	12	9	15	21
Max. Gen. Input kW	5	5	5	7.5	7.5	7.5	12.5	12.5	12.5
These heavy duty cord sets are designed for use with Reliance manual transfer switches, transfer panels and power inlet boxes. UL Listed. Three lengths to choose from.

	Watt Meter Boxes
GeneratorJoe!
	Click on pictures for larger view.
Model Number	MB75	MB125
Components Included/Rating	(2) Watt Meters 3.75 kW each	(2) Watt Meters 6.25 kW each
For Use With Models	Panel/Link®	Panel/Link®
Shipping Weight, lbs	2.5	7.5
Max. Gen. Input kW	2.5	12.5
The Reliance wattmeter boxes are ideal for use with any 125/250VAC installation where balancing the generator load is necessary for optimum performance. UL listed.